Can I Install a Tub Myself? Considerations And Also Steps
Can I Install a Tub Myself? Considerations And Also Steps
Blog Article
On this page in the next paragraph yow will discover lots of high-quality resources regarding A Step-by-Step Guide to Installing a Bathtub.
Setting up a bath tub isn't precisely rocket science, yet it does require strong plumbing, carpentry, and often, tiling skills. Replacing an old tub with a new one is additionally a moderately hard project. If the old bathtub is readily easily accessible, the project can relocate rapidly; if you need to open a wall surface to eliminate the old bathtub as well as place the new bath tub, the task is a lot harder. In either case, the job is within a home handyman's abilities, although you will certainly need a helper to vacate the old tub and also set in the brand-new one. Make certain you have qualified on your own for the job and also are comfortable attempting it. As opposed to employing a service provider to take over a halfway-completed job, it is far better to consider using one before you begin. Opportunities are you may need a specialist plumber to make tube connections.
This short article will certainly assist you mount a new bathtub in your restroom if you have currently gotten a brand-new tub as well as don't need to change the setup of your previous water pipelines.
Your devices as well as material checklist ought to make up the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the limited accessibility that is often the case.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the faucets. Have a towel all set for the staying water that will come from the pipes. Once the supply pipes have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from transforming throughout this procedure. When the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned of any old securing substance.
Prior to carrying on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin making sure that the washers are in area in between the tap and also the sink. Safeguard the tap in place with the supplier supplied backnut. When the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap connectors. The previous type should be attached to the faucet ends initially, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bathtub
Making use of both wood boards under its feet, put the bathtub in the called for setting. The wood boards are practical in equally spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four little points.
The following goal is to make certain that the tub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the bathtub up until the level reads degree.
To set up faucets, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the same for the various other tap.
Turn on the water as well as examine all joints and also new pipework for leakages and tighten them if needed. Fill the tub and also examine the overflow outlet as well as the typical electrical outlet for leakages.
Finally, fix the bathroom paneling as defined in the producer's user's manual. Tiling and sealing around the bath tub needs to wait until the bath tub has been made use of at least once as this will certainly resolve it right into its final setting.
Planning for the Installment
Firstly, the supporting framework provided with the bath must be fitted (if called for) according to the manufacturer's instructions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is essential to see to it that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps device to stop strain on the bath tub.
Fit the adaptable tap connectors to the bottom of the two taps utilizing 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its final position.
Tiling Around the Bathtub
In the area where the bath meets the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the fitting can move enough to crack an inflexible seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, resulting in difficulties with moisture as well as possible leaks to the ceiling below.
You can pick from a range of coloured sealants to blend in your fixtures and also installations. They are offered in tubes and cartridges, and can sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the bath tub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealer can split relatively very early if you do not think about this motion before securing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily readily available on the market. It is advisable to fit the floor tiles using waterproof or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading up on A Step-by-Step Guide to Installing a Bathtub? Put a comment down the page. We would be interested to hear your suggestions about this blog posting. In hopes that you visit us again in the near future. Don't hesitate to set aside a second to share this article if you enjoyed reading it. I cherish reading our article about Installing A Bathtub.
Schedule Now!
Report this page